Grade R3S Offshore Mooring Chain — Stud Link

Grade R3S Offshore Mooring Chain

A strengthened R3 — roughly 12% more yield for the same section, where the design load has outgrown R3 but the toughness requirements of R3 still apply.

Stud link offshore mooring chain to IACS UR W22, grade R3S, in diameters from 50 mm to 90 mm. Quoted on request.

Mechanical properties

Yield stress, minimum	490 N/mm²
Tensile strength, minimum	770 N/mm²
Elongation, minimum	15%
Reduction of area, minimum	50%

Loads, weight and pitch

Diameter	Proof load	Break load	Weight	5-link pitch
50 mm (1.97 in)	1,800 kN 184 t	2,490 kN 254 t	54.8 kg/m	1,100–1,128 mm
52 mm (2.05 in)	1,939 kN 198 t	2,682 kN 274 t	59.2 kg/m	1,144–1,173 mm
54 mm (2.13 in)	2,083 kN 212 t	2,881 kN 294 t	63.9 kg/m	1,188–1,218 mm
56 mm (2.20 in)	2,231 kN 228 t	3,086 kN 315 t	68.7 kg/m	1,232–1,263 mm
58 mm (2.28 in)	2,383 kN 243 t	3,297 kN 336 t	73.7 kg/m	1,276–1,308 mm
60 mm (2.36 in)	2,540 kN 259 t	3,514 kN 358 t	78.8 kg/m	1,320–1,353 mm
62 mm (2.44 in)	2,701 kN 276 t	3,737 kN 381 t	84.2 kg/m	1,364–1,398 mm
64 mm (2.52 in)	2,867 kN 292 t	3,965 kN 404 t	89.7 kg/m	1,408–1,443 mm
66 mm (2.60 in)	3,036 kN 310 t	4,200 kN 428 t	95.4 kg/m	1,452–1,488 mm
68 mm (2.68 in)	3,209 kN 327 t	4,440 kN 453 t	101.3 kg/m	1,496–1,533 mm
70 mm (2.76 in)	3,387 kN 345 t	4,685 kN 478 t	107.3 kg/m	1,540–1,579 mm
73 mm (2.87 in)	3,660 kN 373 t	5,064 kN 516 t	116.7 kg/m	1,606–1,646 mm
76 mm (2.99 in)	3,942 kN 402 t	5,454 kN 556 t	126.5 kg/m	1,672–1,714 mm
78 mm (3.07 in)	4,135 kN 422 t	5,720 kN 583 t	133.2 kg/m	1,716–1,759 mm
84 mm (3.31 in)	4,735 kN 483 t	6,550 kN 668 t	154.5 kg/m	1,848–1,894 mm
87 mm (3.43 in)	5,046 kN 515 t	6,981 kN 712 t	165.8 kg/m	1,914–1,962 mm
90 mm (3.54 in)	5,365 kN 547 t	7,422 kN 757 t	177.4 kg/m	1,980–2,030 mm

Proof and break loads calculated from the IACS UR W22 formulas. Tonnes are metric tonnes-force, given for comparison — the specification works in kN.

Any diameter, not just the ones listed

W22 does not publish a load table — it publishes formulas, so the figures above are calculated rather than looked up and we can quote a diameter that is not on the list. For R3S stud link, with d in millimetres and the result in kN:

Proof load	0.018 × d² × (44 − 0.08d)
Break load	0.0249 × d² × (44 − 0.08d)
Weight, stud link	0.0219 × d² kg/m
Five link pitch	22d minimum, 22.55d maximum

Studless chain is available in every grade. Its break loads are identical to stud link; the proof loads are lower above R3, and weight is calculated per design and submitted to class. Studless is normally deployed once, for permanent moorings with a predetermined design life (W22 §1.1.3).

Accessories — do not substitute anchor chain parts

W22 covers the mooring accessories as well as the chain: common stud and studless links, connecting common links, enlarged links, end links, detachable connecting links, end shackles, subsea connectors, swivels and swivel shackles. Kenter shackles are covered too, with their own machining requirement — the fillet radius must be at least 3 percent of nominal diameter (§3.1.3).

They are made to the R grade, and they are not interchangeable with anchor chain accessories. W22 §1.2.3 is explicit that each grade is approved individually and that approval for a higher grade does not constitute approval of a lower one, and §1.6.1 requires the forge or foundry supplying accessories to be separately approved by the Classification Society. A Grade 3 Kenter made for anchor chain is not an R4 mooring Kenter, whatever the diameter says.

Looking for ship's anchor chain rather than offshore mooring? That is Grade 1/2/3 to IACS UR A1 — see stud link anchor chain and the Kenter joining shackles that go with it.

ORQ — the name this used to have

ORQ, "Oil Rig Quality", is the older name for offshore mooring chain, from before IACS formalised the R grades. It still turns up constantly in enquiries, drawings and rig inventories, and it sits at the bottom of the modern range — broadly where R3 is now.

If your specification, your rig drawing or your old certificate says ORQ, we can quote it. See ORQ and oversize mooring chain.

Larger than 90 mm

The sizes listed match the diameters we carry across the rest of the range, so every chain size has a Kenter joining shackle to pair with it. Above 90 mm the chain is made to order — W22's own tolerance bands run to 222 mm and the formulas above hold the whole way, so we can quote any diameter exactly. Tell us what you need.

Certification

Supplied with Classification Society certification. Chain is manufactured in continuous lengths by flash butt welding and heat treated in a continuous furnace — batch heat treatment is not permitted (§3.2.1.1). Link shape and proportion conform to ISO 1704 or a specially approved design.

Tell us the grade, the diameter, the length and the society, and we will quote it delivered.